Skip to content
CBSHardinPublic

About

For my Bachelor's Thesis, I developed a robotic platform called ARGOS, oriented toward research in multi-robot systems and swarm robotics. This repository provides a concise demonstration of the platform's architecture and operational capabilities.

Topics

Resources

Stars

0 stars

Watchers

0 watching

Forks

Latest commit

 

History

11 Commits

Folders and files

Repository files navigation

20230123_102339

ARGOS

For my Bachelor's Thesis, I developed a robotic platform called ARGOS, oriented toward research in multi-robot systems and swarm robotics. This repository provides a concise demonstration of the platform's architecture and operational capabilities.

Why do you need this? Motivation of the project

Well, at the time of the project, there weren't robotics platforms designed for multi-robot system and swarm robotics easily accessible. Nonetheless, there were a few that could have been used, but some of this platforms were too tailored to a specific set of problems or too expensive to be considerate.

Therefore, the ARGOS robotic platform was born. It incorporates the basics elements you'd need for research in swarm robotics and multi-robot systems:

  • Mobile capabilities: four-wheel drive with individual motors and encoders to enable closed-loop speed control and precise motion tracking.
  • Battery Management Unit: to supervise the state of charge of the battery pack (LiPO chemistry) as well as to protect the user and the robot.
  • 9 axis IMU: accelerometer, gyroscope and magnetometer to implement closed loop pose control and waypoint based navigation.
  • Range and bearing sensor: this sensor allows the robots to locate the relative distance and angle of other agents to enable cooperative behaviors. Additionally, it can function as a reflective LiDAR for nearby obstacle detection.
  • Ultrasonic sensor: forward-facing sensor for frontal obstacle detection and avoidance.
  • Reflectivity floor sensor to detect different zones of operation.
  • A communication system based on ESP-Now.
  • OTA capability: all the robots can be program directly over-the-air.
  • On-board user interface.

It must be noted that all the hardware for this project was developed during the 2020 semiconductor crisis and COVID-19 lockdowns. These circumstances imposed severe restrictions on component availability and, therefore, heavily conditioned the solutions developed. Nevertheless, it was a hell of a lot of fun to fight through it.

See the virtual assembly and the PCBs renders

Virtual assembly

ensamblado_virtual_perspectiva_difuso

Electronic boards

power_board

Powerboard

motherboard_virtual_top

Motherboard

R B_sensor_tx

R&B sensor tx board

placa_sensor_rx

R&B sensor rx board

user_interface_board

User interface board

encoder_virtual_assembly

Encoder's virtual assembly

Check the demo of the Range and Bearing Sensor

The design of the range and bearing sensor required a considerable amount of time, but it was paramount to the project. It was based on the work of Jim Pugh, Alcherio Martinoli, et al [1], as well as the concepts developed by James F. Roberts et al [2].

Test_sensor_RB_reduced_quality.mp4

It should be noted that in order to guarantee high precision (measurement repeatability) and an operational range of 4 meters, a thorough theoretical analysis was conducted regarding both the maximum allowable noise level and the gain of the amplification stages on the RX board. If you are working on a similar problem, I hope this provides some inspiration, as I found very little literature available on the subject.

Not just hardware

The full scope of the project wasn't only "design a robot", the full scope of the project was design a toolkit that could be used to research in swarm robotics. Usually, research or just try out a new idea requires invest effort and time on the boilerplate part of the idea. This'd lead to waste resources to just get to the starting point. As consequence, to extract the maximum value, this platform aiming to be a fast-prototyping platform for mobile robots using alike ecosystems.

For to accomplish this goal, it was mandatory to hide all the complexity involved in control systems, sensors, pose estimation, communications, etc and the real time constrains imposed by all of them. To allow the researcher to focus on the algorithm instead the platform, an API based in FreeRTOS was designed. This allows to hide all the complexity of the systems control; and at the same time, it satisfy the real time constrains.

Moreover and following the goal of fast-prototyping, Arduino IDE was selected as the IDE for the toolkit. A new core was designed to incorporate a port of FreeRTOS and to adapt some core's code. In addition, the tools for OTA (over-the-air programming) were integrated seamless in Arduino IDE though the new core. This simplify the tedious process of deploying a new program to simple click in the Arduino IDE's programming button.

oap_integración_arduino

More info

You could find more info of the project at the bachelor's dissertation, available in the digital archive of the Universidad Politécnica of Madrid (UPM), linked here.

References

[1] - J. Pugh, A. Martinoli, and F. Engineering, "A Fast On-Board Relative Positioning Module for Multi-Robot Systems," in Proc. IEEE/RSJ Int. Conf. Robot. Autom., 2009, pp. 4501–4506.

[2] - J. F. Roberts, J. Pugh, and A. Martinoli, "2.5D Infrared Range and Bearing System for Collective Robotics," in Proc. IEEE Int. Conf. Robot. Autom., 2009, pp. 2379–2384.

About

For my Bachelor's Thesis, I developed a robotic platform called ARGOS, oriented toward research in multi-robot systems and swarm robotics. This repository provides a concise demonstration of the platform's architecture and operational capabilities.

Topics

Resources

Stars

0 stars

Watchers

0 watching

Forks

Releases

Packages

Contributors

Languages